汽车侧滑测量系统的设计

范文编号:JD545 范文字数:18455,页数:42

摘 要
实践证明，汽车的侧滑会造成滚动阻力增加、行驶稳定性变差、轮胎磨损加剧、运行油耗增多和转向沉重等问题，影响了汽车的使用性和经济性，所以必须对汽车的侧滑进行定期检测。本文介绍了一种汽车侧滑测量系统的硬件及软件的设计方法，该系统由输入系统、输出系统和80C51单片机系统构成。测量系统把传感器传来的频率信号转换成对应的侧滑量，显示在液晶显示器上。如果测量超过上限，自动发出报警声提示。测量系统通过串行口可把测量的结果发送到上位机。本文主要完成汽车侧滑测量系统的硬件设计及软件设计。在硬件方面，详细介绍了位移检测电路，液晶显示电路，报警电路等等。在软件方面，介绍了主程序的流程图及各部分电路的编程方法。
本设计具有结构简单，实用性强，可靠性高，不易损坏等特点，适用于大部分汽车侧滑的测量，可以满足大部分生产厂家的要求。

关键词：上位机，下位机，单片机，显示器

Design of the sideslips measurement system of automobile
Abstract
The practice proves that the automobile sideslips can sharply increase the rolling resistance, make the driving stability become badly, accelerate the tire abrasion, waste much more and more oil and turn around heavily, affect handling property and economical efficiency of the automobile. So the automobile sideslips must be checked up for a fixed interval. This article introduces hardware and software system of automobile sideslips, principle of automobile sideslips and others principal factors. The sideslips system of automobile is constituted by input system, the output system and 80C51 micro controller unit. The measurement system accepts the signal of this sensor and then converts the signal to the sideslips value, which is displayed on the liquid-crystal display at last. If the value of sideslips goes beyond, the annunciator can send out warning tone automatically. The system of measurement can also send the measuring result to upper computer by serial port. This article mainly completes hardware and the software design of measure system of the automobile sideslips. In the hardware aspect, it introduces circuit of detection, circuit of liquid crystal display, warning circuit and so on. In the software aspect, it curtly introduces flow chart of main program and the programming method of all ports of circuit.
This design has such characters, it is suit for the simple, the high reliability, not easy to damage and so on. Automobiles sideslip system and satisfy the majority of autobile manufacturer the request.

Keyword: Upper computer、Lower computer、Micro controller Unit、Display
目  录
摘 要 1
Abstract 2
1 绪  论 5
1.1  汽车侧滑测量系统的设计前景 5
1.2  影响汽车侧滑的因素 5
1.3  国内外关于汽车侧滑测量系统研究的状况及相关成果 6
1.4  本设计的相关内容 7
2 系统的硬件设计 8
2 .1 总体框图及简介 8
2.1.1 系统的总体设计 8
2.1.2 系统的基本工作过程 9
2.2  MAX485芯片简介及其特点 9
2.2.1 单片机与MAX485标准远距离通讯介绍 10
2.2.2 MAX485芯片原理图及通信原理 10
2.3 传感器的组成及其分类 12
2.3.1 传感器的选择及原理图 13
2.3.2 光栅位移传感器原理 14
2.4  8051单片机的简介 15
2.4.1 程序存储器2764 15
2.4.2 数据存储器2864 16
2.5 报警电路原理 17
2.6 LCD显示器 17
2.6.1 显示驱动器 19
2.6.2 位选电路 19
3系统软件的设计 22
3.1 汇编语言 22
3.1.1 汇编语言的概述 22
3.2 主程序框图 23
3.3 系统软件设计的主要功能模块 24
3.3.1 报警模块 24
3.4 部分程序设计 25
3.5 初始化程序 27
结  论 29
致  谢 30
参考文献 31
附录A（英文参考资料） 32
附录B（中文翻译） 37
附录C（总体设计原理图） 42

 《汽车侧滑测量系统的设计》WORD格式全文下载链接