DX型钢丝绳芯带式输送机

范文编号:JX127 所有图纸,范文字数:23982.页数:73

摘    要
带式输送机自它诞生以来，经过200多年不断完善和改进，已进入电力，冶金，煤炭，化工，矿山，港口等各行各业之中。其机构简单，输送物料范围广，输送量大，运距长，对线路适应性强，装卸料十分方便，可靠性高，营运费低廉，基建投资省，耗能低，效率高，维修费少。
本设计为DX型钢丝绳芯式带式输送机，采用机头双滚筒驱动，在保证滚筒不发生打滑的前提下来传递较大的功率，降低输送带的张力和提高使用寿命。文中根据第二滚筒围包角用足，依此算出输送机的各种参数，进行结构设计。由于倾角较大，按第二滚筒围包角用足进行等驱动功率单元法分配，本设计采用分配，得出尾部张力最小，根据布置原则，张紧装置一般布置在输送带张力最小处，所以本文采用重载车式张紧装置进行张紧。如今，带式输送机正向长距离、高带速、大功率、大运量的大型化方向发展，使其在煤炭行业得到广泛应用。

关键词  带式输送机  双滚筒驱动 

Abstract
The belt conveyer with continue development and improvement has entered all trades and professions such as power, metallurgy, coal, chemical engineering, mine and port since being born for more than 200 years. Its construction is simple , it is broad to transport stock scope, it is big to transport quantity, the length of haul distance has strong adaptability for line, handling material is very convenient, reliability is  high , it can reduce investment in basic construction, high efficiency, low maintenance cost.
The design is DX model core type belt conveyer of wire rope, the  machine header adopts two cylinder drives ,in guarantee cylinder do not occur the prerequisite with slippery dozen transmit greater power, reduce raising the tension of belt conveyer and improve service life. In writing according to second cylinder surround bale angle use enough, according to this various parameters that make conveyer finally, carry out structural design. Since inclination is greater, according to second cylinder wait for drive with foot power unit law distribution, this design adopts 1: 1 is distributed , it is minimum to reach tail tension, basis arrange principle, tension station arranges normally, is in the tension minimum place of conveyer belt , so, this paper use the burden vehicle tension equipment to tighten. Now belt conveyer’s development towards to long distance, high belt speed, great power and high transportation, and the advantage of this kind of conveyer realizes easily, make extensive application in coal industry.

Keyword    Belt conveyer     two cylinder drive   tight

目  录
摘    要 ...........................................................I
Abstract ...........................................................II

第1章  绪  论 ......................................................1
1.1 前言 ...........................................................1
1.2 带式输送机的发展史 .............................................1
1.2.1国外带式输送机的发展 ..........................................1
1.2.2国内带式输送机的发展 ..........................................2
1.2.3国内外带式输送机的差距 ........................................2
1.2.4带式输送机的发展趋势 ..........................................3
1.3 带式输送机的分类............................................... 3
1.4 带式输送机的特点及应用......................................... 4
第2章 带式输送机的整体设计方案 .....................................5
2.1 方案的确定 .....................................................5
2.2 工作原理....................................................... 7
第3章  带式输送机的主要部件与功能.................................. 10
3.1 输送带......................................................... 10
3.1.1输送带的发展 ..................................................10
3.1.2输送带的种类及差异 ............................................10
3.1.3输送带的要求.................................................. 11
3.1.4钢丝绳芯输送带 ................................................11
3.2 拉紧装置 .......................................................12
3.2.1拉紧装置的作用 ................................................12
3.2.2拉紧装置的分类及特点 ..........................................12
3.3 托辊 ...........................................................14
3.3.1托辊的结构及作用.............................................. 14

3.3.2托辊的选择.....................................................14
3.4清扫装置........................................................ 16
3.4.1清扫器的作用.................................................. 16
3.4.2清扫器的形式 ..................................................16
3.5 传动滚筒、改向滚筒............................................. 17
3.5.1传动滚筒的分类 ................................................17
3.5.2改向滚筒的选取................................................ 18
3.5.3环形胀套 ......................................................19
3.6 机架的设计与选取 ...............................................20
3.6.1机头探架...................................................... 20
3.6.2中间支架...................................................... 20
第4章 带式输送机的设计计算......................................... 21
4.1 设计参数....................................................... 21
4.2 根据实际输送量计算带宽......................................... 21
4.3 运行阻力 .......................................................23
4.4 牵引力及运行功率............................................... 28
4.5 输送带张力计算 .................................................29
4.6 输送带强度验算 .................................................31
4.7 滚筒直径的确定 .................................................31
4.8驱动装置的选型及计算 ............................................32
4.8.1电动机的选型.................................................. 32
4.8.2液力偶合器的选型 ..............................................32
4.8.3减速器的选型.................................................. 33
4.8.4联轴器的选型 ..................................................36
4.8.5制动器的选型及计算 ............................................37
4.9 拉紧力计算..................................................... 40
4.10 托辊的选取 ....................................................41
4.10.1 静载荷计算.................................................. 41
4.10.2 动载荷计算 ..................................................43
结  论 .............................................................45
致  谢 .............................................................46
参考文献........................................................... 47
附录1 ..............................................................49
附录2.............................................................. 56

 《DX型钢丝绳芯带式输送机》WORD格式全文下载链接